I’m sure I’m massively overthinking this, but any help would be greatly appreciated.

I have a domain name that I bought through NameCheap and I’ve pointed it to Cloudflare (i.e. updated the name servers). I have a Synology NAS on which I run Docker and a few containers. Up until now I’ve done this using IP addresses and ports to access everything (I have a Homepage container running and just link to everything from there).

But I want to setup SSL and start running Vaultwarden, hence purchasing a domain name to make it all easier.

I tried creating an A record in Cloudflare to point to the internal IP of my NAS (and obviously, this couldn’t be orange-clouded through CF because it’s internal to my LAN). I’m very reluctant to point the A record to the external IP of my NAS (which, for added headache is dynamic, so I’d need to get some kind of DDNS) because I don’t want to expose everything on my NAS to the Internet. In actual fact, I’m not precious about accessing any of this stuff over the internet - if I need remote access I have a Tailscale container running that I can connect to (more on that later in the post). The domain name was purely for ease of setting up SSL and Vaultwarden.

So I guess my questions are:

  • What is the best way to go about this - do I create a DDNS on the NAS and point that external IP address to my domain in Cloudflare, then use Traefik to just expose the containers I want to have access to using subdomains?
  • If so, then how do I know that all other ports aren’t accessible (I assume because I’m only going to expose ports 80 and 443 in Traefik?)
  • What do other people see (i.e. outside my network) if they go to my domain? How do I ensure they can’t access my NAS and see some kind of page?
  • Is there a benefit to using Cloudflare?
  • How would Pi-hole and local DNS fit into this? I guess I could point my router at Pi-hole for DNS and create my A records on Pi-hole for all my subdomains - but what do I need to setup initially in Cloudflare?
  • I also have a RPi that has a (very basic) website on it - how do I setup an A record to have Cloudflare point a sub-domain to the Pi’s IP address?
  • Going back to the Tailscale thing - is it possible to point the domain to the IP address of the Tailscale container, so that the domain is only accessible when I switch on the Tailscale VPN? Is this a good idea/bad idea? Is there a better way to do it?

I’m sure these are all noob-type questions, but for the past 6-7 years I’ve purely used this internally using IP:port combinations, so never had to worry about domain names and external exposure, etc.

Many thanks in advance!

  • schmurnan@lemmy.worldOPEnglish
    0·
    1 year ago

    Update from this morning.

    So far I’ve got the Traefik dashboard and my Homepage container using subdomains. Pi-hole is still an issue that I need to figure out.

    I’ve decided to start on the SSL certificates and am following a couple of guides. Once I have those in place, I’ll start moving more containers behind subdomains.

    I might have to expose my NAS IP to the internet and link it via Cloudflare, because I use an ExpressVPN on my Mac at all times, and when it’s turned on I can’t access ***any ***of my subdomains - this is obviously because ExpressVPN use their own DNS entries and don’t use the ones I’ve set. That will probably prevent me from using Vaultwarden (which is the whole purpose for all of this in the first place) because if I’m on the VPN I won’t be able to access the Vaultwarden container.

    Unless anyone knows of a workaround for that?

    Next steps:

    • Get SSL working
    • Figure out how to access subdomains whilst on the VPN (or get a DDNS account, create an A record in Cloudflare and point it at the DDNS IP, and open up ports 80 and 443)
    • Spin up a Vaultwarden container via a subdomain
    • Put all my other services behind subdomains
    • Figure out how to get Pi-hole working via Traefik and subdomain
    • Figure out how to get Tailscale access to my containers when not on my LAN
    • schmurnan@lemmy.worldOPEnglish
      1·
      1 year ago

      Just a quick update on where I’m up to…

      I’ve managed to get all my containers working behind the Traefik reverse proxy with SSL. I’ve also deployed a Cloudflare DDNS container in Docker and have linked the external IP address of my Synology NAS to Cloudflare. I haven’t port forwarded 80 and 443, though, so it’s not accessible over the internet. So I’ve added local DNS into Pi-hole so I can access all the containers using subdomains.

      I’ve also deployed an Authelia container and have started running through my containers adding 2FA in front of them all.

      I should probably point out at this juncture, that if I encounter any errors, the HTTP 404 page that I get is a Cloudflare one - I assume that’s expected behaviour?

      So, the final three bits I’m struggling with now are:

      • Pi-hole behind the reverse proxy
      • Portainer behind the reverse proxy
      • Accessing Vaultwarden over the internet (because as soon as I leave my house, if the vault hasn’t synced then I don’t have access to all my passwords) - unless anybody has a better suggestion?

      Portainer - I have no idea how I do it, because I use it to manage my containers, so don’t have the config for Portainer in Portainer (obviously). So if I screw up the config, how am I getting back in to Portainer to fix it?

      And the far more troubling one is Pi-hole. I just cannot get that thing working behind the reverse proxy.

      I’ve followed a few different guides (though none of them are recent), and the below is the latest docker-compose I have. It will bring up the login page, but when I login it keeps returning me back to the login page - it won’t go to the main admin page.

      version: "3.7"

services:
  pihole:
    container_name: pihole
    image: pihole/pihole:latest
    restart: unless-stopped
    networks:
      - medianet
      - npm_network
    ports:
      - 8008:80
      - 53:53/tcp
      - 53:53/udp
    environment:
      - TZ=Europe/London
      - WEBPASSWORD=xxxxxxxxxx
      - FTLCONF_LOCAL_IPV4=192.168.1.116
      - WEBTHEME=default-auto
      - DNSMASQ_LISTENING=ALL
      - VIRTUAL_HOST=pihole.mydomain.com
    volumes:
      - /path/to/pihole:/etc/pihole
      - /path/to/pihole/dnsmasq.d:/etc/dnsmasq.d
    cap_add:
      - NET_ADMIN
    labels:
      - traefik.enable=true
      - traefik.http.routers.pihole.entrypoints=http
      - traefik.http.routers.pihole.rule=Host(`pihole.mydomain.com`)
      - traefik.http.middlewares.pihole-https-redirect.redirectscheme.scheme=https
      - traefik.http.routers.pihole.middlewares=pihole-https-redirect
      - traefik.http.middlewares.pihole-addprefix.addprefix.prefix=/admin
      - traefik.http.routers.pihole.middlewares=pihole-addprefix
      - traefik.http.routers.pihole-secure.entrypoints=https
      - traefik.http.routers.pihole-secure.rule=Host(`pihole.mydomain.com`)
      - traefik.http.routers.pihole-secure.tls=true
      - traefik.http.routers.pihole-secure.service=pihole
      - traefik.http.services.pihole.loadbalancer.server.port=80

networks:
  medianet:
    external: true
  npm_network:
    external: true