Those are just fake vests bought specially for that purpose. Nobody would think to take off their actual vest at the last gathering for the school year.

Correcting the reviewer.
Notes: “should of” isn’t valid, should implies a verb, of isn’t a verb. I expect you meant “should have”. Please recall this in future submissions.

Sailor is worn out after that red sea voyage.

I haven’t found anything solid. It’s dropped off my plate for now.

I will probably end up self hosting some xmpp for it.

Nope, found my problem with the install of mainsail being a permissions thing.

I’m still running the stock board, but have upgraded to a remote direct drive extruder.

Eventually nobody.

Capitalism isn’t about sustainability, it’s about making the most amount of profit in the shortest amount of time.

Eventuall you bleed everyone dry and nobody has a job. But for a short amount of time the shareholders will have had a huge number of 0’s and 1’s in a database somewhere equating to their “worth”

You do understand how much energy (and therefore pollution) it takes to launch any significant mass above the karman line, right?

I have enphase inverters as well. I don’t find their data to be useful.

I went the route of installing two circuit setup boards running esp8266. One is installed in the subpanel in the garage where the solar feeds, the other is installed at the main panel on the main cables before any loads.

This way I can more accurately see production and usage. And can tell during production how much I’m actually utilizing before sending residual back to grid.

If I had only one panel and the solar fed directly into it, I’d use one of the 6 channel circuitsetup boards instead to monitor both solar feed and main.

Setup a self hosted media server, put your media on it, stream from that.

Would this not require a battery as well, as usually the light is only lit while the door is open.

Making vacation even worse for said battery.

Proton has stopped the “visionary” that allows SMTP, now it’s only available in business accounts. :( I tried setting up the bridge CLI, but so far haven’t been able to get it to send anything after logging in and syncing the account, Maybe I’ll try again once I’ve got some things off my plate.

Setup rules that forward to an IP:port I used a guide on smarthomebeginner initially. I’ll try and find it found it.

Go here https://www.smarthomebeginner.com/traefik-docker-compose-guide-2022/

And scroll till the section. “Adding non-docker or external apps behind Traefik”

The rich are on the top decks where the valve controls are, they don’t have wet feet, why should they close the valves?

Not really a feature of the phone, but a design theory. I want my small phone back. Not this “zenfone 9” size small. Like HTC One size small.

Make it bifold wallet sized, and ~1/2"thick.

These hugely tall phones where you can’t reach the top third if the screen without dropping the thing are just annoyingly huge. Then they make them so thin they can’t fit a big enough battery for a full day use.

Beyond that would like an under display fingerprint sensor. Rear and side mounted always have issues with cases for me, and make it more annoying when using the device while it’s on a desk.

Time to code your own thermostat.

An esp32, a 4x or 8x relay board, and a 24vac to 5vdc rectifier/regulator and you’re golden.

Even has WiFi ;)

This is likely the problem. I’ll try it when I get off work.

Thanks!!

Hardware is a Pi4, 4GB. I’ve looked through the log, don’t know how to upload file here for you to look through it, and it’s too long for character limit. It does indicate issues with the serial port, either permission denied in the case i tried tty0 symlink, or no such file or directory when going strait to the serial/by-id.

I’ve tried many setups. First was following https://www.klipper3d.org/Installation.html#obtain-a-klipper-configuration-file With octopi. Next was another guide that I can’t seem to find the link to again. But was a default raspbian lite x32, and installing klipper and mainsail on top with kiauh. next was this guide https://www.obico.io/blog/install-klipper-ender-3/ which I modified for the Ender5+ (what processor to compile for)

I’ve had varying success, initial try the USB wouldn’t show in serial/by-id, I swapped cables and still had no entry. Swapped cables back and tried the next guide/OS, and that gave me the entry in serial/by-id.

also I Tried using the symlink tty0, but that didn’t work either.

For the current OS/Setup I think i’ve messed with too many things, and just need to start over from fresh OS. But I can’t think of anything different to try.

Ah, look at the titanic while shitting in an outhouse sized tube with 4 other people… What an experience

Jack and charger ports can be controlled by the phone to turn off if there is low resistance (ie water) between contacts.

A battery is harder, as it’s what provides the power to the thing that decides whether to turn off the port. Not that it’s impossible to put some smarts into a battery, to decide when to power the output. But it’s going to add a lot of complexity and bulk to do it (switching circuit, logic circuits, etc)

I see it as a longevity thing.

Sure you can bring another battery pack with you and charge your device from it, but at some point your internal battery will be degraded enough that it essentially needs to be plugged in to function, which is not feasible.

Being able to easily replace the thing in the device that wears out fastest is a good thing.

Granted I expect if this does go through, that mfg will make the battery hard to replace by other means (ie drm locks) making sure they can nickel and dime the consumer all the way.