I used to be scared to fly in a helicopter. Then I learned how they fly. Now I’m scared when they fly overhead.
I used to be scared to fly in a helicopter. Then I learned how they fly. Now I’m scared when they fly overhead.
… You won’t have a name when you ride the big airplane All they will call you will be “deportee”… https://music.youtube.com/watch?v=awKLW7WgGB8&si=uknAHeB2oFiVV5Fv
Skip the toilet paper and install a bidet.
I’ve got several years of experience riding motorcycles. It’s taught me to read traffic. I see a gap in a line of traffic like that, it’s either a driver who’s smart enough not to block an intersection (rare), or someone letting another someone out.
By your logic, Israel’s government is just as culpable: https://www.timesofisrael.com/for-years-netanyahu-propped-up-hamas-now-its-blown-up-in-our-faces/
The IDF claims that the children would have been Hamas operatives, on account of who their parents were. It’s not hard to extend that reasoning to the grandchildren. After all, their parents were likely to be Hamas operatives as well.
No judge, no jury, just an executioner, based solely upon the IDFs word that they’re likely to become future terrorists. One might apply that same logic to the whole of Palestine.
No, I think I read you perfectly.
If your society is content with murdering children based on your belief of what they will grow up to be, it’s not a society I’d be comfortable being part of, associating with, or existing alongside.
May you be judged accordingly.
Well, what’s out there?
More for the rest of us!
Not if it leads to your excuses and justifications of “war was always like this. No need to change it.”
Absolutely disgusting, down to the very core of my being. I want nothing to do with your beliefs.
Be better.
It tastes like sarcasm.
This whole thread is sarcasm, dipped in a whipped sarcasm batter, crusted with crushed sarcasm, then deep fried in a pure sarcastic oil for a sarcastically long time until it’s a nice even color. It’s then drizzled with a sarcastic reduction, and presented on china with a sarcastic pattern with accompanying cutlery.
I’ll do that. Should I be using the “Ender-3 4.2.2 mainboard (32bit)” firmware? I’ve read that the Marlin firmware isn’t compatible with the GD CPUs, so I’m assuming the “Ender-3Marlin2.0.6HW4.2.2GD” won’t work.
Update: support got back to me, with instructions to reflash using the latter firmware. The symptoms changed: during the firmware “upgrade”, the 05 LED flashes about once a second. I let it run for ten minutes, but the printer never rebooted. Powered it off, removed the SD card, powered it back on… Still nothing but a blue display, though the 05 LED keeps blinking once a second.
I’m thinking it’s a bad motherboard. Waiting on support, now.
I’ve got a laptop running Linux on it; connected it up at some point during my time with it. The laptop was able to see the USB to serial adapter, but I didn’t poke at it to see if anything was talking on the other side. I’ll try that today!
Checked for that, too. Both the original panel and the replacement only have one “port” for the cable on the back. The board has spots for two more to be connected, but both are missing. Looking at the front of the panel (as if I’m using it), the port is the left most of the three.
Gentoo. I’d tell you the version number, but I’m still compiling.
Just the basic Ender 3, I believe. No version number, so implied v1. Not a Pro, SE, or other appendment to the model.
That’s next on my list, if the replacement panel doesn’t fix the issue. Figured I’d go with the obvious solution first. Doesn’t help that I took a long look at the list of the firmware available for the Ender 3, and figured I’d cross that bridge another day. Creality does not make it simple to identify what’s what.
After reading through your post history, all I can say is “Bullshit.”