• Drudge@lemmy.worldOP
    link
    fedilink
    English
    arrow-up
    3
    ·
    1 year ago

    Well I moved it up by around 3mm on the bar…so if the current print turns out, I’m good.

    What upgrades were you thinking?

    • 𝑔𝑎𝑙𝑎𝑥𝑖@lemm.ee
      link
      fedilink
      English
      arrow-up
      5
      ·
      1 year ago

      You should look into a dual gear extruder. They’re a slight upgrade from this kind and do a lot better without wearing out. If you want a bigger upgrade though, look into a BMG clone. It’s great for direct drive if you decide that you want to do that at some point. It has a 3:1 gear ratio so you’d need to adjust e-steps, but it’s really efficient.

      • Drudge@lemmy.worldOP
        link
        fedilink
        English
        arrow-up
        2
        ·
        1 year ago

        Thanks for the recommendation… Do you have a link to a good one? Seems like there’s a ton of option on Amazon.

        What’s the benefits of a direct drive?

        • j4k3@lemmy.worldM
          link
          fedilink
          English
          arrow-up
          4
          ·
          1 year ago

          Direct drive requires less retraction by like an order of magnitude which speeds up printing. There isn’t the tension that builds up like a spring in the Bowden tube.

          The precision of the extruder components is really important. The Bowden setup is less critical to an extent. This guy explains the issues really well here:

          https://piped.video/watch?v=c6JmCdovE0U

        • 𝑔𝑎𝑙𝑎𝑥𝑖@lemm.ee
          link
          fedilink
          English
          arrow-up
          1
          ·
          1 year ago

          I also recommend the trianglelab BMG extruder from aliexpress. They’re the king of clones. Otherwise, just go for anything with a good amount of reviews on amazon. They aren’t too expensive. Most of us who’ve been printing long enough have a drawer full of extruder parts :p

          Direct drive not only lets you print with flexible filament and more precision like the others mentioned - but I also prefer it to bowden because over time, the tubing will get melted and you’ll need to snip off the end. With direct drive, it’s usually only an inch of tube that you can just replace. With bowden, you can end up either decreasing your hotend’s reach (tube gets too short) or have to buy and install a whole new length. Plus, direct drive means faster reload time, less things going wrong. You may just need to get a light stepper motor or compensate other ways with direct drive, as the main downside is the potential for ringing due to a heavier hotend. I don’t notice it much, but that would be the trade off.

        • Flaky_Fish69@kbin.social
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          dd’s give better retraction and can offer better precision, especially with flexible filament

          Bowden can print much faster because the print bead weighs substantially less and introduces less patterning

    • Flaky_Fish69@kbin.social
      link
      fedilink
      arrow-up
      3
      ·
      edit-2
      1 year ago

      If you need an upgrade (or want, heh.)… I doubt you can go wrong with microswiss. At least, I never have. (Their nozzles are my bread and butter, too)

      Micro Swiss has an amazing dual gear for Bowden tubes. They’re advertised as fitting creality machines but they basically just sit on top of the motor, so as long as your motor is the same size you can make it work.

      Of course any of their direct drive extenders are definitely worth it

    • Gormadt@lemmy.blahaj.zone
      link
      fedilink
      English
      arrow-up
      1
      ·
      1 year ago

      I personally have Titan extruders on both my FDM machines

      They’re great IMO

      I hear that Revo hemera are pretty cool but they’re kind of expensive

      There’s also the orbiter extruder which looks pretty cool too